Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
The content following next about A Step-by-Step Guide to Installing a Bathtub is truly enlightening. You should give it a look.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is readily accessible, the task can move speedily; if you need to open a wall surface to remove the old bathtub and place the new bath tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub as well as embeded in the new one. Make sure you have actually certified yourself for the task and fit trying it. As opposed to hiring a contractor to take over a halfway-completed task, it is much better to think about using one before you start. Chances are you might require an expert plumber to make tube links.
This post will help you install a new bathtub in your restroom if you have currently bought a brand-new bathtub and do not require to alter the setup of your previous water supply pipes.
Your devices and product list need to consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is separate the supply of water. After doing so, activate the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic because of the restricted gain access to that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipes. Once the supply pipes have been removed, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Before carrying on to fit the new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and the other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin making certain that the washing machines are in place in between the faucet and also the sink. Secure the tap in position with the supplier given backnut. When the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former type needs to be connected to the faucet finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bathtub
Using the two wood boards under its feet, position the bathtub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto four little factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the bath tub till the level reviews degree.
To mount taps, fit the bottom of the furthest flexible tap connector to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the supply of water and also inspect all joints and brand-new pipework for leakages and tighten them if necessary. Load the tub as well as also examine the overflow outlet as well as the regular outlet for leakages.
Lastly, fix the bath paneling as defined in the maker's user's manual. Tiling and also securing around the bathtub needs to wait till the bath tub has been utilized at least when as this will certainly settle it into its last position.
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bathroom should be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its last setting.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and also the tiling, causing issues with moisture and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can crack rather early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently available on the marketplace. It is suggested to fit the tiles making use of waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Hopefully you enjoyed reading our piece about Installing A Bathtub. Thank you for finding the time to read our piece. Sharing is nice. You just don't know, you might be doing someone a favor. Kudos for your time. Please visit our blog back soon.
Get relief now! Report this page